I think this journal is good, it pays a lot of attention to coating and the preparation process of coating. I have had several articles in it. The speed of reviewing is quite fast. Generally, 40-50 days after submission, the reviewer (generally 3 reviewers) comments, and their opinions are objective and comprehensive. Although the number of manuscripts is relatively large, the speed of review is not slow. The articles generally take about 4 months from submission, through major reform, and then to acceptance, but it is very likely that articles will be accepted directly after the major changes. The impact factor in 2010 has risen to more than 2, and it is gratifying! At the same time as the impact factor is rising, the difficulty of being accepted is also rising. Our research team has submitted a total of 9 times since 2009, only 4 articles have been accepted, all after major reform.

(0) Thank | Anonymous

26 Nov 2018 Submitted12 Feb 2019 AcceptThe speed is very fast, and the middle has been overhauled. Editing S.M.A. Shibli, Ph D is very fast, and it is the result of the day.I hope that SCT will be better and better.

(1) Thank | 妞妞XC

October 30, 2018 submitted to journalNovember 27 major revisionSubmitted by December 14thMin 4 revision of January 4, 2019Submitted on January 9thJanuary 10 acceptEditing by Claus G. Rebholz is very timely!The first SCI, the work of the New Year, continues to work hard.

(11) Thank | 冲鸭！！！

October 3th submitted to journalOctober 4 under reviewOctober 11 under reviewNovember 8 minor revisionNovember 26, revised submittedNovember 27 with editorNovember 29 acceptSCT is also a relatively recognized journal in the industry. The above is the experience of this submission.The review speed is not slow, and it is less than 2 months before and after.Editing Professor Aouadi is also very responsible for the processing!Must continue to support in the future!

(4) Thank | 随便取个名字

Just submitted, step by step recording process18 Aug 2018 Submitted to journal20 Aug 2018 With Editor

(2) Thank | xjr@glut.edu.cn

Very good journal, 2.25 contribution, overhaul during the period, returning to 5.28, receiving 6.20, editing is very nice, reviewer is also very responsible, for the quality of the articleThe improvement is greatly helped, and it is important to carefully modify and improve according to the deficiencies raised by the reviewers.

(0) Thank | 科研小白

11月23Submission, December 1st to the editor's hand, dragged on for a long time on the 13th for review, did not expect a reviewVery fast, returning to the overhaul on the 31st, as of February 14th, the two reviewers, the opinion is not particularly good, to make up the test.The draft was submitted on February 6th, submitted to the trial on February 9th, and received on February 22nd. It was finally relieved.

(2) Thank | 菜大叔

Three shots three refusals, transferred to journal of materials science Directly acceptd two articles

(3) Thank | 德州扑克

Too too slow!The draft submitted at the end of September began to be under review at the end of November, and has been under review until now!!!It is useless to write a letter to the Lord. If the manuscript can be retracted, it will be withdrawn. The heart plug

(1) Thank | 啊啊啊啊啊啊

11月23Submission, December 1st to the editor's hand, dragged on for a long time on the 13th for review, did not expect isThe review was very fast. On the 31st, the opinions were overhauled. As of February 14th, the two reviewers were not particularly good. They had to make up the test and hoped that there would be a good result after the change.

(0) Thank | 菜大叔

Too too slow, from submission to editing for eight days, now has been in the editor for ten days, still not submitted for review.....

(0) Thank | 菜大叔

6.17Submission8.2 overhaul9.16 Submitting overhaul results10.10 minor repair10.11 Submitting minor repair results10.12 minor repair10.13 ReceivingThe first article, thank you very much for editing the impurities, very fast!

(0) Thank | yilan

5月13日稿Review the draft for one month,Revise the manuscript for a month and a half,Received on August 24th.It's a holiday, maybe the editor is busy, and it's been a long time to edit it.

(1) Thank | 田秋实

The submission period is too long, and the review is strict, but it is helpful for improving the quality of the article.

(1) Thank | ioe

The journal is still good, I hope the review speed can be faster

(2) Thank | 小徐

real-time impact factor: 2.533

(2) Thank | a

Real-time impact factor: 2.515

(0) Thank | a

real-time impact factor: 2.430

(0) Thank | 11

Submit directly after submission, one month before and after, the review is very fast, and the idea needs new.

(2) Thank | Anonymous

Excuse me, is this article about the direction of grease lubrication in this journal?

(0) Thank | zhxsh77@126.com

After 4 months of overhaul, it will be accepted in two months, lasting 6 months, the speed is very slow, I hope IF up

(0) Thank | 123

selectd for three weeks, or Submitted to Journal, be careful

(2) Thank | 1247514463@qq.com

4 months later, now 6 months passed, the speed is very catchingUrgent ah

(0) Thank | yyanghit@hotmail.com

Journals have high requirements for paper innovation, short publishing period, and 2 district journals, which are worthy of submission.

(9) Thank | 707597049@qq.com

The review is faster, the journal has high requirements for the quality of the paper, the paper needs to be innovative, and the 2 district journals have a low impact factor!

(14) Thank | 1440643219@qq.com